How to Install a Pocket Door
What is a pocket door? And how do you put in a pocket door? Discover the recommendations and tricks for putting in a pocket door to help save floor place from a common hinged door swing. An great remedy for compact areas or uncomfortable door parts.
For additional compact place alternatives, try out these: Suggestions to make a compact place experience open up, our Foldable Craft Table, and a Smaller place research or workplace station.
In advance of we exhibit you how to put in a pocket door — let us response the most frequent question:
What is a pocket door?
A pocket door is a sliding door on a track inside the wall. Exactly where a sliding barn door and the barn door components are on the outdoors of the wall, a pocket door and pocket door components are installed inside the wall and completely concealed.
Concealed pocket doors are fantastic alternatives for compact areas and 50 % loos, because they help save the floor place from a common hinged door swing, when however presenting additional privacy than a barn door. Pocket doors are also completely concealed when open up, so they don’t have to have any adjustment to your wall decor either.
Related Reading through: Do-it-yourself Barn Doors and Barn Door Components
For our pocket door put in, we experienced a 50 % bath at the conclude of a hallway, with the door swinging out. We desired a pocket door! You can see previously mentioned how the door opened up into the hall and, with children, it was just constantly open up. Throughout the hall was our bed room doorway, so it was blocked and the shots on the wall ended up only 50 % obvious.
Not the look and experience we ended up heading for (primarily with our new board and batten wainscoting all around the dwelling) and it was bad for the going for walks targeted visitors flow, so a pocket door was the way to go for us. I Highly propose a prebuilt pocket door kit and here’s how the method goes:
How To Set up A Pocket Door
*Bear in mind, before starting up any job that impacts the framework of your dwelling be absolutely sure to seek the advice of with a structural engineer or architect!*
Update March 2019: We installed yet another pocket door in our present-day dwelling and designed a video clip to exhibit you the method! Test it out more than on our YouTube channel:
Materials and equipment for pocket door frame installation
This article consists of affiliate one-way links. Discover additional and study our comprehensive disclosure plan right here.
Action 1: Pick the locale
This nice blank wall with no electrical or plumbing inside designed the excellent place for a pocket door.
Action 2: Clear away the existing door
Ahh… the distinction it would make to take off the door! The fantastic matter about putting in a pocket door is that when you take off the existing door, you can see accurately how the place will experience when you are done: nice and open up, no door blocking your route! 
Action 3: Hold drop cloths
In advance of starting up any demo, put up some drop cloths to consist of all. the. dust. (This drop fabric is hung in the place that shares the wall the pocket door is heading into.)
Action four: Clear away drywall
The pocket door will go in the wall that is amongst the 50 % bath and our master rest room shower, so we lower out the drywall on the 50 % bath side quite cautiously (We even retained it in 1 piece and reinstalled it! NO squander!). We scored the walls deeply at all the corners, then lower as a result of the other sections and used a crowbar to gently pop the nails out of the again of the drywall (you can also use a reciprocating noticed to lower the nails to get you began).
In this article is the huge piece of drywall at the time removed…
Action 5: Clear away studs
Following, we eradicated the studs and header exactly where the pocket door kit will go. (We did not make a momentary wall due to the fact this dwelling has two parallel walls within just 3 feet on either side. If you do not have those people supporting walls, you might will need to construct a momentary wall before getting rid of the studs. Consult with a contractor, if desired.)
We used a reciprocating noticed to lower the nails so that the studs could be reused.
Action six: Develop a door frame
Justin began with a new header, and set the jack and king studs in place. (Jack usually means the 1 supporting the header and the king is the comprehensive peak stud that sits outdoors the header.)
Action seven: Incorporate the pocket door kit
Now that the door framing is in place, the easy component is introducing the pocket door kit. Generally, it is a slot (pocket) with place for the door to slide into and a track on best.
Use shims to make certain it sits in the good place.
Action eight: Put together the existing door, if desired.
Incorporate the track components to the existing door employing the guidelines that occur with the pocket door kit. Also remove the previous door knob and hinges and put in a deal with plug, if you will need 1.
Action 9: Hold the door
And the remaining benefits? Pocket door perfection… very well, practically!
It reached perfection when we installed all the door trim and a nice coat of black paint to match the other doors!
Look how open up and unobstructed the place is now! I hung new family pictures when all the wainscoting and trim was up… like it!)
If you want to see the first article about the 1/2 bath look at it ou
t right here!
Make sure you adhere to alongside with us on Pinterest, YouTube, Instagram and Fb.
And uncover additional fantastic door tutorials, this sort of as:
Revealed Aug 22 2012 // Up-to-date Apr 20 2020
Related
