How to Build a Banquette

Up for a amazingly straightforward weekend project? Consider it or not, you can make your own banquette out of stock kitchen area cabinets, a few of two-by-fours, and a cozy cushion. Comprehensive the appear with an assortment of graphic and solid-coloured throw pillows.

See down below for phase-by-phase directions from Allie Mann of Case Architects & Remodelers to get started off on your banquette.

Supplies Necessary

• Degree
• Speed square
• Measuring tape
• Pencil
• Nail or screw gun with trim nails or trim screws
• 2×4 lumber materials (total will depend on the dimension of the banquette)
• 1×4 lumber materials (total will depend on the dimension of the banquette)
• 1×2 lumber materials (total will depend on the dimension of the banquette)
• Window sill materials
• ¼” thick birch plywood
• ¾” thick birch plywood
• Building glue
• Round observed
• Stock wall cabinets, 12” tall and 12” deep, width dependent on room.

How to Develop the Banquette

• Identify wished-for dimension of banquette seating (stock cabinets occur in 3” increments, so if you intend to use the banquette for storage, keep this in intellect). The cabinets should not sit tight wall-to-wall. There should be a filler or piece of trim concerning the box of the cupboard and the wall to allow for the door to open up.
• Frame the system of the bench using the 2×4 lumber materials.
• Frame a knee wall or partial wall at cupboard peak to attach the cupboard using the 2×4 lumber materials.
• Protected bench frame to wall, alongside with knee wall and cabinetry, using nail or screw gun.
• Reduce the ¼ ” birch plywood on round observed to wrap the toe kick room (this will be painted later on).
• Reduce the ¾” birch plywood on the round observed for the wood top. When measuring the plywood top, allow a ¾” overhang in front of the cupboard door this would be a 1.5” overhang from the genuine cupboard box.

How to Develop the Banquette Wall Trim

• Following, measure, lower, and apply a piece of ¼ birch plywood to the wall—the size of the bench—using your end screws and glue. The piece of plywood and bench together should end 48” tall higher than the end ground, building the plywood piece all over 30– 32” tall.
• Following, apply a 1×4 horizontal piece to produce the rectangular box higher than the bench at the top and bottom of the plywood piece.
• Evaluate, lower, put, and attach the 1×4 vertical parts on the plywood with screw or nail gun. Be confident the wainscot rectangles mimic the identical width as people on the bench cupboard if doable. These rectangles you are developing on the wall will very likely be concerning 18” – 24” wide.
• End top of the wainscot rectangle with the window sill trim materials or the 1×2 lumbar (calculated, lower, and nailed in put).
• Caulk and putty any seams, gaps, fill holes, etcetera.
• Sand, prime, and paint the plywood.

  Buy Anything You Have to have to Develop a Banquette

  Multipurpose Laser Degree

  Qooltek
  amazon.com

  $15.98

  Speedlite Sq. Layout Instrument

  Swanson Instrument Co., Inc
  amazon.com

  $four.98

  Max twenty five ft. x 1-1/8 in. Tape Evaluate

  Stanley
  homedepot.com

  $8.70

  Reversible Drywall Screw Gun

  DEWALT
  homedepot.com

  $ninety nine.00

  Weighty Responsibility Building Adhesive

  Liquid Nails
  homedepot.com

  $two.57

  Unfinished Stock Cabinet

  Undertaking Resource
  lowes.com

  $fifty eight.48

  PureBond Birch Plywood

  Columbia Forest Solutions
  homedepot.com

  $27.72

A model of this function appeared in the July/August 2020 difficulty of Very good Housekeeping.

This content material is produced and preserved by a third occasion, and imported on to this web page to aid customers offer their email addresses. You could be equipped to come across additional data about this and equivalent content material at piano.io

This commenting segment is produced and preserved by a third occasion, and imported on to this web page. You could be equipped to come across additional data on their web web-site.